Low Voltage Panels

01. Power Control Centres (PCC Panels)

BRITE ENGINEERS Has been manufacturing CPRI tested Power Control Centre Panels up to 4000A as per IEC 60439 & IEC 61439 & supplying to reputed Domestic & International customers since Last 25 years.

The complete structure shall be rigid; a semi modular design, self-supporting & free from twists and bends. The panels will be totally dust and vermin proof. The enclosure will undergo pre-treatment covering decreasing, water rinsing & de-rusting/ phosphating. It will be synthetic enamel painted or powder coated as per requirements.

Bus Bars & Internal Wiring Uniform cross section of Aluminium / copper Bars (current density as per the relevant IS / IEC) supported by SMC /DMC bases will be employed throughout the length of the panel. Internal wiring be carried out with 11000 / 690 volt grade PVC insulated stranded FRLS wires. All joints will be solidly crimped using copper thimbles, copper Earthing Bus Bars will be running all along the board.

By default we offer ABB Air Circuit Breakers with Microprocessor based releases.

All the meters, CTs, Relays, Indicators, push buttons, Rotary switches, Connectors, MCBs, MCCBs used will as per the approved makes given by the customer.

Standard Specifications of a 3 Phase, 50Hz LV PCC:

02.

Motor Control Centres - MCC Panels & IMCCs

BRITE ENGINEERS are one of the leading manufacturers of Motor Control Centre Panels widely used and appreciated across the country & abroad.

We manufacture panels of Single front & Double front design as per the site requirements, both Fixed and draw out type as per the application and form of construction up to form-4B.

We also manufacture Intelligent Motor Control Centres IMCC’s) with communication & Central monitoring & operation of all the feeders from SCADA. Complete status will be available on a mobile phone

Key Features of our Motor Circuit Control Panel

Custom Design
Fixed type / Draw out type, free standing, floor mounting
Extendable to both sides
Cubical type compartmentalised construction
Busbar made of electrolytic grade, aluminium alloy / copper with certified % IACS conductivity
Short circuit withstand capacity of 50kA for 1 sec RMS
Switchgear and control gear as per customer’s choice
Top or bottom cable entry
Front and Rear Access
Single / Double front construction
Designed to meet climatic conditions
Powder-coating with imported electrostatic powder gun and fully conveyorised powder-coating plant
Design facilitating adequate space for cable and bus duct termination and providing required cable support
All live parts are properly shrouded by means of acrylic sheet in order to ensure no accidental contact with live parts during maintenance

03.

Automatic Power Factor Control (APFC) Panels

Automatic Power Factor Control Panels are mainly used for the improvement of Power Factor. Power Factor can be explained as ratio of active power to apparent power and it is a key factor in measuring electrical consumption. Everyone knows that how costly electricity has become in present time. Therefore it becomes utmost important to cut down on electrical consumption for reducing expenditure.

Automatic Power Factor Control Panel come real handy in the achievement of this purpose Use of these control panels becomes indispensable in those industries where electrical installations are meant to supply to large electrical load. A dip in Power Factor can attract operational losses and a penalty from electricity board, responsible for electricity supply.

We offer vide range of standard and customized APFC panels and are competitive in the industry.

Automatic Power Factor Control Panel can effectively and automatically manage quickly changing and scattered loads along with the retention of high Power Factor. We are renowned manufacturers of APFC Panels symbolized with quality and reliability. These are available in different current ratings to cater to distinct applications.

The main features of our control panels are:

Maintains high Power Factor constantly
High efficiency
In-built independent fuses
Protection from excess power in the system.
Prevents leading Power Factor in low load conditions
Clearly marked buttons and indicators
Minimizes harmonic current
Easy to use
Corrosion-resistant
Long lasting
Electrical insulation
Protects electrical equipments

04.

DG AMF Panels

BRITE ENGINEERS manufactures Auto Mains Failure Control panels which are used widely in foundries, apartments, textiles and other varied industries. Our panel comes with various functions and timers which help in the efficient running of the AMF panels. It also consists of the metering facilities for monitoring of the frequency / current / voltage. We can also customize it according to the client specifications and details.

We offer automatic mains failure panels or automatic AMF panels that are installed for automatic changeover from mains to stand-by generator at the time of power failure. Fabricated from premium quality raw material, these automatic AMF panels are durable, corrosion resistant, dust and vermin proof. Easy to operate and install, these synchronized AMF panels are used in areas like foundries, apartments, textiles, sugar and chemical industries.

Features:

Provides continuous monitoring of three-phase
Voltage/current/frequency of mains & DG
As well as battery voltage of DG
Available in different models
Automatic shutdown during DG fault
Fault indication via LED/LCD
Configurable solid state output
Auto/Manual Selector is available
Auto delay in start of genset
Genset stop with delay of 3 minutes
Hooter-alarm annunciation for fail to start
Checklist to find the fault and to correct
4st switch control for healthy start and stop of genset
Manual Start & Stop Switch
Emergency Stop switch is available
Auto LLOP (Low Lube Oil Pressure) and (High Water Temperature) protections are available. (LLOP & HWT Sensors-Relays are not part of this panel. We provide control wires. Generally generator technicians shall provide this safety sensors according to their Generator’s standard.)
Cost of 2nos of 4st/Qst switches and 12V heavy-duty stop solenoid are added
All comes in a 14 /16 Swg panel with door.

05.

DG Synchronization Panels

We are specialized in offering synchronized AMF panels, which are widely appreciated by our clients for corrosion resistance and easy operations. Manufactured using superior quality material, these synchronized AMF panels are extensively used for automatic changeover from mains to stand-by generator at the time of power failure. Designed in compliance with the international standards of quality, these synchronized AMF panels are ideal for places where the generators are installed between main AC and load.

Features

Paralleling up to 10 + DGs at a time
All DGs connected through a SCADA, monitoring & operation from a single point
Use of High end DG Synch Relays of reputed makes as per customer requirements
Load Manager, Power reverse protection Earth fault, filed lost control, auto manual synchronisation, dual volt meter, dual frequency meter, all comes in a single panels.
Automatic start and stop of the generator and changeover the EB/generator lines
Auto/manual selector is available
Auto delay in start of gen set
Gen set stop with delay settings
Hooter-alarm annunciation for fail to start
4ST switch control for healthy start and stop of gen set
Manual start & stop switch
Available with emergency stop switch
Auto LLOP (Low Lube Oil Pressure) and (High Water Temperature) protections are available (LLOP & HWT Sensors-Relays are not part of this panel

06.

LV Bus Ducts

BRITE ENGINEERS manufacture best quality Bus Ducts that can be customized as per the customer’s requirements. All these products are specially designed for different industrial applications are designed to provide better connection, superior performance and more security. We have a fully equipped facility with the latest and most sophisticated machines. These Ducts also go through stringent quality checks at all levels. These products can also be customized as per client’s requirements.

Features

Air Insulated metal enclosed Bus Ducts CPRI type tested up to 4000Amps 50kA
Phase segregated & non segregated metal enclosed bus duct
Bus Duct with required rating, Fault Level.
Designing of Bus Duct to achieve required Fault Level, considering temp. Rise, Thermal Rating, Stress, withstand capacity and all applicable derating factors.
Bus Duct up to 4000A With Copper/ Aluminium Bus bar.
Bus bar Supported on DMC/SMC Support.
Bus bar with Heat Shrinkable Sleeve.
Indoor / Outdoor Duty, Separate adapter at both end With Space heater and earth Bus.
Enclosures can be powder coated/ GI / Aluminium depending on specifications & ratings

07.

Feeder Pillars

BRITE ENGINEERS is in to manufacture of 6, 12, 16, 32 & multiple way Feeder pillars for BESCOM and other ESCOMS applications, They consist of a Fuse Switch Unit / MCCB as an incomer & MCBs / Fuses as Feeders.

08.

Distribution Boards & Junction Boxes

BRITE ENGINEERS Manufacture Distribution boards for all applications & Junction boxes for most of the industrial application with MS & Aluminium Enclosures as per customer requirements.